Back to Resource Center

Panasonic OLED and LCD AutoCal Guide

For compatible Panasonic 2020-2023 OLED and LCD models, Calman can automatically calibrate the TV’s two-point white balance controls, the 12-point grayscale controls, and the CMS color gamut controls in Standard Dynamic Range (SDR) mode, High Dynamic Range (HDR) and Dolby Vision modes. This assures the most accurate rendering of picture content.


Each step of this workflow has been optimized to display relevant information, and automatically configure common settings. Both Pre-Calibration and Post-Calibration measurement steps are included for comparing pre- and post-performance.


Calman Required Version
  • Calman Studio, Video Pro, or Ultimate
  • For instructions on Calman Home for Panasonic see This Article
Calman Required Workflows
  • AutoCal – Panasonic
Required Hardware
  • HDR and Dolby Vision Compatible Pattern Generator
  • HDR Compatible Meter
  • Compatible Panasonic TV
    • Panasonic – 2020 HZ Series
    • Panasonic – 2021 JX (LCD) Series (JX850, JX900, JX950)
    • Panasonic – 2021 JZ (OLED) Series (JZ980, JZ1000, JZ2000)
    • Panasonic – 2022 LZ (OLED) Series
    • Panasonic – 2022 LX (LCD) Series
    • Panasonic – 2023 MZ (OLED) Series
    • Panasonic – 2023 MX (LCD) Series

Jump To


SDR Calibration

Step 1

  • From the Calman Menu in the top-left, choose Open Workflow Template -> Display Specific and then AutoCal – Panasonic
  • Click SDR Calibration on the first page to proceed to hardware connection

Connect your Colorimeter and Pattern Generator to Calman.

  • Plug your meter into a USB port on the computer and press the Find Meter button on the left
    • When your meter is connected, select your display type from the dropdown (this will vary by meter)
  • Connect Pattern Source to your computer. If you are using the Panasonic internal pattern generator, see this article for setup instructions
    • Click the Find Source button then select your source
    • Select the pattern window size
      • Window 10%

Connect to, and prepare your Panasonic TV for calibration

  • Connect the Calman computer to the same network to which the Panasonic TV is connected.
  • Under Menu\Network\Network Status\Status Details note the IP address.
  • On the Panasonic TV, open the Picture menu
    • Under Picture\Viewing Mode, select Professional 1 or Professional 2
    • Under Picture\Lock Settings, enter PIN i-0-8-5
    • Arrow down to ISFCCC Network and press OK on the remote.
      • An HDMI signal must be fed into the TV and selected as the input.
        • The ISFCCC Network option does not display when you are using one of the App inputs, like Netflix
      • This option will be disabled if the PIN is not set to i-0-8-5
      • In some regions, this option may be disabled in firmware. Contact Panasonic support for your region for more information.
    • At this point, the TV will read “Waiting for Connection
  • Click on the Find Display button, select your Panasonic model
  • Under Socket Connection, enter the TV’s IP Address that you noted above.
  • Click Connect on the Find Display dialog.
  • Select Picture Mode to Calibrate.
    • Using the picture mode dropdown menu to the right, select which picture mode you would like to calibrate.
      • Options are Pro 1 – Day or Pro 2 – Night

Step 2

Confirm your calibration targets and prepare TV
  • Press Reset Targets
  • For SDR, calibration targets should be:
    • Rec709
    • D65
    • BT.1886
  • Hardware Options
    • Pattern Size: Window 10
    • Pattern Insertion: ON
      • Frequency 45
      • Duration 5
      • Intensity 25

Step 3

In this step, you’ll take readings of your display before the calibration. These will be used to compare your calibration results
  • To take Pre-Calibration Measurements click the Read Series […] button to measure the display’s grayscale and ColorChecker response
    • This will provide a point of reference to compare your calibration results

Step 4

  • Select your target picture mode
    • Options are Pro 1 – Day or Pro 2 – Night
  • Press Full DDC Reset
    • This will configure several of the TVs settings to the ideal values. 

Step 5

In this step, you will be able to adjust the Luminance of your display to match your desired target. Luminance is a subjective target. SDR reference luminance is 100cd/m2, but you may need to target higher to account for the ambient light in your environment.
  • Click the Measure Luminance button to measure your TV’s light output at 100% white and adjust the display’s peak white to the desired luminance.
    • Luminance is a subjective target. SDR reference luminance is 100nits, but you may need to target higher to account for the ambient light in your environment.
  • Adjust your TV’s backlight/OLED light control so your TV is about 15% brighter than your final target to account for a reduction in luminance when calibrating the 1D LUT in the next step
  • Press Stop when luminance adjustment is complete

Step 6

On this page, Calman will adjust your display’s White Balance
  • Click the AutoCal button to perform the 2pt greyscale AutoCal
  • Click Next after AutoCal has completed to confirm the gamma response and setting of your TV align with your targets

Step 7

Here Calman will adjust the Multipoint Greyscale of your display.
  • Press the AutoCal button and select the SDR greyscale points on the AutoCal dialog

Step 8

Here you will be able to manually adjust your Brightness and Contrast to ensure the display is not clipping away any RGB values near white
  • Adjust the display’s Brightness and Contrast controls to set dynamic range (black to peak white).
    • In most cases, the default brightness and contrast values are appropriate for calibration
  • Click the Brightness button to display the brightness pattern then adjust brightness manually.
  • Click the Contrast button to display the contrast pattern then adjust contrast as high as possible without blending the brightest gray bars together and without shifting their color.
  • In the Datapoint levels drop-down, select Clipping with Peak White (90-109%), unless your pattern source does not generate patterns over 100% white, then select Clipping (90-100%).
  • Click the Read Series button and view the clipping detector graph chart to verify the Contrast adjustment.
  • If the RGB signals plateau at peak levels, reduce the Contrast slightly and retest.
  • Select the 100/235 pattern, click the Read Continuous button, and adjust the display’s peak white to the desired luminance from Step 5

Step 9

On this page, Calman will adjust the Colorspace/CMS controls on your display
  • Press the AutoCal button to open AutoCal dialog
    • All options are preconfigured
  • Click OK to begin colorspace AutoCal process

Step 10

Post-calibration readings to document the post-calibration condition of the display.
  • Click the Read Series […] button

SDR Calibration is now complete


HDR Calibration

Step 1

  • From the Calman Menu in the top-left, choose Open Workflow Template -> Display Specific and then AutoCal – Panasonic
  • Click HDR Calibration on the first page to proceed to hardware connection

Connect your Colorimeter and Pattern Generator to Calman.

  • Plug your meter into a USB port on the computer and press the Find Meter button on the left
    • When your meter is connected, select your display type from the dropdown (this will vary by meter)
      • OLED: White-OLED (OLED (White) LG, Panasonic, FSI 2018 for C6 Meter)
  • Connect Pattern Source to your computer. If you are using the 2019 Panasonic internal pattern generator, see this article for setup instructions
    • Click the Find Source button then select your source
    • Select the pattern window size
      • Window 10%

Connect to, and prepare your Panasonic TV for calibration

  • Connect the Calman computer to the same network to which the Panasonic TV is connected.
  • Under Menu\Network\Network Status\Status Details note the IP address.
  • On the Panasonic TV, open the Picture menu
    • Under Picture\Viewing Mode, select Professional 1 or Professional 2
    • Under Picture\Lock Settings, enter PIN i-0-8-5
    • Arrow down to ISFCCC Network and press OK on the remote.
      • This option will be disabled if the PIN is not set to i-0-8-5
      • In some regions, this option may be disabled in firmware. Contact Panasonic support for your region for more information.
    • At this point, the TV will read “Waiting for Connection
  • Click on the Find Display button, select your Pansonic model
  • Under Socket Connection, enter the TV’s IP Address that you noted above.
  • Click Connect on the Find Display dialog.
  • Select Picture Mode to Calibrate.
    • Using the picture mode dropdown menu to the right, select which picture mode you would like to calibrate.
      • Options are Pro 1 – Day or Pro 2 – Night
    • Choose Color Gamut: BT.2020
    • Check the HDR Checkbox

Step 2

Confirm your calibration targets and prepare TV
  • Press Reset Targets
  • For HDR, calibration targets should be:
    • rec.2020
    • D65
    • ST.2084
  • Hardware Options
    • Pattern Size: Window 10
    • Pattern Insertion: ON
      • Frequency 5
      • Duration 5
      • Intensity 25

Step 3

In this step, you’ll take readings of your display before the calibration. These will be used to compare your calibration results
  • To take Pre-Calibration Measurements click the Read Series […] button to measure the display’s grayscale and ColorChecker response
    • This will provide a point of reference to compare your calibration results

Step 4

  • Select your target picture mode
    • Options are Pro 1 – Day or Pro 2 – Night
  • Press Full DDC Reset
    • This will configure several of the TVs settings to the ideal values.
      • Note: If values are being reset to incorrect values, ensure HDR Checkbox is checked in Step 1

Step 5

On this page, Calman will adjust your display’s White Balance
  • Click the AutoCal button to perform the 2pt greyscale AutoCal

Step 6

Here Calman will adjust the Multipoint Greyscale of your display.
  • Press the AutoCal button and select the HDR10 or HLG greyscale points on the AutoCal dialog, depending on your calibration targets

Step 7

On this page, Calman will adjust the Colorspace/CMS controls on your display
  • Press the AutoCal button to open the AutoCal dialog
    • All options are preconfigured
  • Click OK to begin the colorspace AutoCal process

Step 8

Post-calibration readings to document the post-calibration condition of the display.
  • Click the Read Series […] button

HDR Calibration is now complete


Dolby Vision Calibration

Step 1

  • From the Calman Menu in the top-left, choose Open Workflow Template -> Display Specific and then AutoCal – Panasonic
  • Click Dolby Vision Calibration on the first page to proceed to hardware connection

Connect your Colorimeter and Pattern Generator to Calman.

  • Plug your meter into a USB port on the computer and press the Find Meter button on the left
    • When your meter is connected, select your display type from the dropdown (this will vary by meter)
      • OLED: White-OLED (OLED (White) LG, Panasonic, FSI 2018 for C6 Meter)
  • Connect Pattern Source to your computer. The Panasonic internal pattern generatorcannot be used for Dolby Vision calibration
    • Click the Find Source button then select your source
    • Select the pattern window size
      • Window 10%

Connect to, and prepare your Panasonic TV for calibration

  • Connect the Calman computer to the same network to which the Panasonic TV is connected.
  • Under Menu\Network\Network Status\Status Details note the IP address.
  • On the Panasonic TV, open the Picture menu
    • Under Picture\Viewing Mode, select Professional 1 or Professional 2
    • Under Picture\Lock Settings, enter PIN i-0-8-5
    • Arrow down to ISFCCC Network and press OK on the remote.
      • This option will be disabled if the PIN is not set to i-0-8-5
      • In some regions, this option may be disabled in firmware. Contact Panasonic support for your region for more information.
    • At this point, the TV will read “Waiting for Connection
  • Click on the Find Display button, select your Panasonic model
  • Under Socket Connection, enter the TV’s IP Address that you noted above.
  • Click Connect on the Find Display dialog.
  • Select Picture Mode to Calibrate.
    • Using the picture mode dropdown menu to the right, select which picture mode you would like to calibrate.
      • Options are Pro 1 – Day or Pro 2 – Night
    • Choose Color Gamut: BT.2020
    • Check the HDR Checkbox

Step 2

Confirm your calibration targets and prepare TV
  • Press Reset Targets
  • For HDR, calibration targets should be:
    • rec.2020
    • D65
    • ST.2084
  • Hardware Options
    • Pattern Size: Window 10
    • Pattern Insertion: ON
      • Frequency 5
      • Duration 5
      • Intensity 25
  • Enable Dolby Vision on your pattern generator.  Configure your Dolby Vision metadata to Absolute
  • Click Next
  • A Dolby Vision verification screen will appear to verify that the Dolby Vision signal is being interpreted properly

Step 3

In this step, you’ll take readings of your display before the calibration. These will be used to compare your calibration results
  • To take Pre-Calibration Measurements click the Read Series […] button to measure the display’s grayscale and ColorChecker response
    • This will provide a point of reference to compare your calibration results

Step 4

  • Select your target picture mode
    • Options are Dolby Vision Dark or Dolby Vision – IQ
  • Press Reset Dolby Vision
    • This will configure several of the TVs settings to the ideal values.
      • Note: If values are being reset to incorrect values, ensure HDR Checkbox is checked in Step 1

Step 5

On this page, Calman will adjust your display’s White Balance
  • Click the AutoCal button to perform the 2pt greyscale AutoCal

Step 6

Here Calman will adjust the Multipoint Greyscale of your display.
  • Press the AutoCal button and select the Dolby Vision greyscale points for your model on the AutoCal dialog

Step 7

Here you will create the Dolby Vision Config File to finalize calibration

  • Click on the Create Dolby Vision Config button, to create a custom Dolby Vision config file, consisting of White, Black, Red, Green, and Blue measurement data.
  • After the config file has been created, it will be loaded to the TV automatically

Step 8

Post-calibration readings to document the post-calibration condition of the display.
  • Click the Read Series […] button